View and Download Kawasaki Ninja R service manual online. Ninja R Motorcycle pdf manual download. Also for: Ninja er-6f, Ninja er-6f abs. Visit Kawasaki Motor Corps., USA owners center for up to date service manuals, parts diagrams, ROK™ info, owner support, warranty info, Kawasaki Protection. Ninja R. ER-6f. ER-6f ABS. Motorcycle. Service Manual. All rights reserved. No parts of this publication may be reproduced, stored in a retrieval system, or.
|Published (Last):||18 October 2015|
|PDF File Size:||8.74 Mb|
|ePub File Size:||3.87 Mb|
|Price:||Free* [*Free Regsitration Required]|
Run the rear wheel rotation sensor lead into the clamps.
Crankshaft Sensor Owjers Voltage 2. Torque – Grab Rail Mounting Bolts: Ball Bearing and Needle Bearing Do not remove pressed ball or needle unless removal is absolutely necessary. Fuel line clogged Inspect and repair see chapter 3. Gaskets, O-rings, oil seals, grease seals, circlips or cotter pins must be replaced with new ones whenever disassembled.
Air Switching Valve 2. Overall Iwners 1 mm This digit in the frame number changes from one machine to another.
Be sure to use the dedicated electrolyte container for correct electrolyte volume. Head Pipe Outer Race Driver, For these reasons, Kawasaki does not recommend temporary exter- nal repair. Battery 12 V 10 Ah Set it close to the bottom of the cylinder, where cylinder wear is low. Stick coil shorted or not in good contact Inspect or Reinstall see chapter Subthrottle Sensor Lead 7. If they are badly worn or if there are groove cuts where the tangs hit, replace the housing.
Special Tools and Sealant Battery 12 V 10 Ah 8. Special Tools and Sealant Hand Tester: Band Hold the main harness in rear of the frame cross pipe.
Year of ,anual registration: Clutch Lever and Cable Clutch not disengaging Engine oil level too low Shift fork bent or seized Engine oil poor quality or incorrect Gear stuck on the shaft Gauge incorrect Throttle Cable Decelerator 4.
Cylinder head gasket damaged Spark plug loose Cylinder head warped Cylinder head not sufficiently tightened Valve spring broken or weak down Valve not seating properly valve bent, No valve kawasaji worn, or carbon accumulation on mahual Cylinder, piston worn seating surface Piston ring bad worn, weak, broken, or Kawasaki Bond Liquid Gasket kawaswki Black: If it is damaged, replace it.
Kawasaki Ninja R Service Manual – ZX6R Forum
Reserve Tank Over Flow Hose 4. If this accumulation is not removed, it will clog up the water passage and considerable reduce the effi- ciency of the cooling system.
Align the clamp knob with the red paint as shown in the figure. Bands Hold ownere main harness between the frame pipe and fuel tank bracket. Torque – Swingarm Pivot Shaft Nut: If there is any doubt as to the condition of the reeds, re- place the air suction valve as an assembly.
Inlet Air Temperature Sensor http: Vacuum Pressure Absolute to Sensor Vv: Torque – Brake Pedal Bolt [E]: Torque – Clutch Spring Bolts: Sealant – Kawasaki Bond Silicone Sealant: If the frame is bent, dented, cracked, or kawwsaki, replace it. Right City Light Lead Connector 5. Do not drop or shock the valve seat cutter, or the dia- mond particles may fall off.
Steering Stem Bearing Driver, Oxygen Sensor Equipped Models If there is the continuity in the lead, replace the ABS hy- draulic unit. Throttle Cable Decelerator 7. All information contained in this publication is based on the latest product information available at the time of publication.
locate a dealer
If the seal is torn or is leaking, replace the bearing. Inlet Air Temperature Sensor Standard Atmospheric Pressure Absolute Pv: Starter Circuit Relay 9.
Clamp Install the clamp with the quick rivet onto the throttle body assy. Be sure to maintain proper alignment and use smooth movements when installing. Throttle Cable Accelerator 6. Throttle Cable Decelerator 2. If there is any irregularity, replace the drive chain.
Align the paint of the reserve tank hose with the reserve tank projection.