Amercoat Chemical Resistant Lining. Product Data/. Application Instructions. • High Solids, high performance epoxy novolac also defined. Amercoat – Download as PDF File .pdf), Text File .txt) or read online. This Safety Data Sheet is prepared in accordance with Annex II to Regulation ( EC) No. / AMERCOAT CHEMICAL LINING CURE.
|Published (Last):||17 February 2008|
|PDF File Size:||20.78 Mb|
|ePub File Size:||1.94 Mb|
|Price:||Free* [*Free Regsitration Required]|
Warranty HTC warrants that its products are free from defects in material and workmanship. Do not use brush with synthetic bristlesand brush out the blister before it sets. Abrade surface per ASTM D to remove all efflorescence and laitance, to expose sub-surface voids, and to provide a surface roughness equivalent of 60 grit sandpaper or coarser. Suitable for seawater immersion in combination with controlled cathodic protection systems.
Add hardener to base and agitate with a power mixer for minutes until completely dispersed. Surface must be power washed as needed to remove all surface contaminants including zinc salts and alkaline salts formed during the curing process. This tool should be used as a guide only. This document will only discuss interior substrates and is not intended to be a technical discussion of More information.
Non-ferrous metals Remove oil or soap film with detergent or emulsion cleaner as per SSPC SP-1 and galvanizing requirements, then use a phosphatizing conversion coating. This is not to be confused with burned areas and does not require special treatment. Pacific Southwest Coatings specializes in performance coating solutions for corrosion, abrasion, extended life cycle performance, marine, offshore, chemical containment, biological containment, high temperature, fire protection and commercial architectural specialty applications.
When re-coating within 72 hours, solvent wipe the surface with Amercoat thinner prior to application of the second coat. Use good painting practices. Concrete Remove all surface contaminants such as oil, grease, and embedded chemicals. Hi-Temp VHA has excellent spray application properties and is resistant to cobwebbing.
Chemical Resistant Lining Product Data Application Instructions High Solids, high performance epoxy novolac also defined as phenolic epoxy tanklining Exceptional resistance to a broad range of chemicals, solvents and fuels Two or three coat system Outstanding Characteristics Amercoat Chemical Lining provides excellent protection to prepared steel and amercoat pdf Safety Data Sheets SDS If you cannot find a specific MSDS, please contact your PPG representative or email us here specifying the product, country and language page33 AMERCOAT Dry times are dependent on air and surface temperatures as well as film thickness, ventilation, and relative humidity.
Alternately, power tool clean to uniformly abrade the surface or lightly abrasive blast with a fine abrasive to produce a uniform and dense anchor profile of mils. There are many different varieties of. Do not apply over galvanizing, zinc coatings, or concrete. For paint and recommended thinners see safety sheetand relevant material safety data sheets This is a solvent borne paint and care should be taken to avoid inhalation of spray mist or vapor as well as contact between the wet paint and exposed skin or eyes.
A suitably finished surface must have a uniform surface texture exposing fine aggregate resembling coarse sandpaper.
Performance Industrial, Marine and Commercial Coating Systems
Amerlock Sealer will amber with age. Higher surface temperatures shorten the maximum recoat window Surface must be clean and dry.
Apply Amercoat when Amerlock Sealer is still wet or tacky. Hi-Temp VHA is a user-friendly system, which can be brushed and rolled.
Mechanical surface preparation should expose sub-surface voids and provide a surface profile equivalent to 60 grit sandpaper or coarser.
Pour the liquid into the mixing vessel. Gradually add powder and mix until the cement is uniformly blended to a workable consistency. Amerlock 2VOC is compatible over most types of properly applied and tightly adhering coatings, however, a test patch is recommended to confirm compatibility.
Applicable over surface treatments such as MIL-C Alternately, lightly abrasive blast with fine abrasive to produce a uniform and dense anchor profile of mils. Avoid over-blasting as pin-point rusting may develop. My Basket Log in. Prime concrete with Amerlock Sealer or Amerlock When a pinhole-free coating is required, check continuity of dry, but uncured coating with a nondestructive amercost detector such as a Tinker-Rasor Model AP at approximately 15, volts.
Amercoat – [PDF Document]
Ensure good ventilation during application and curing. Do not allow Prep 88 to dry on the surface. Un-insulated steel Do not exceed recommended dry film thickness Primer Hi-Temp to 6. Higher surface ameercoat up to 5 mils are acceptable, but the product must be applied in a thickness great enough to achieve a minimum of 2. Hi-Temp s sole obligation and buyer s exclusive remedy shall be limited to replacement of products not conforming to this warranty. Available in 2-gallon and 5-gallon kits 2-gallon kits have 1 full gallon zmercoat base and 1 full gallon of hardener 5 gallon kits have 2.
Surface temperatures should be monitored, especially with sunexposed or otherwise heated sur amercoat pdf Amercoat Chemical Lining is packaged in the proper mixing proportions of resin and cure. Ensure there is a moisture and oil trap amefcoat the main air line. Product can be un-topcoated in certain applications. Periodically check wet film 25 during application with a steel rule depth gauge or other suitable wet film thickness gauge.
Thinner Amercoat H is typically used without thinning.