What is CO-OSP? • Customer Owned Outside Plant. • “Telecommunications infrastructure designed for installation exterior to buildings”. ANSI/TIA/EIAA . Active, Most Current. BUNDLE AND SAVE: Item is contained in these product bundles. EN. Additional Comments: ANSI APPROVED. Format. TIA/EIA Engineering Standards and Publications are designed to serve the public Outside Plant Telecommunications Cabling Standard (ANSI/TIA/EIA).
|Published (Last):||6 August 2006|
|PDF File Size:||3.9 Mb|
|ePub File Size:||16.18 Mb|
|Price:||Free* [*Free Regsitration Required]|
Conduit ends to be plugged at time of placing both ends.
No details or procedures are specified for doing these functions required under OSHA regulations for prevention of accidental underground facility damage.
These include flood water or chemical exposure, sub-immersion in ice, and exposure to steam or fire. Jumper wire may be 26, 24, or 22 AWG copper. Backbone cabling is also used to interconnect entrance facilities such as telco demarcation points to the main eiw.
Underground or direct-buried pathways are generally preferred over aerial pathways because of aesthetics and security. Damage prevention laws usually specify the location of eiia zone.
In addition, the polarity of tip and ring of each pair shall be identified. TIA does not enforce or monitor compliance with the contents of the Document. Accommodations should be made for diverse APs. At these temperatures it is necessary that the closure not experience any functional degradation that could affect the performance of the closure.
Aerial cable is typically lashed to a cable-support strand messenger.
The basic requirements for design are as follows: This standard specifies the cabling, pathways and spaces to support the cabling. Minimum breaking strength for spliced wires of smaller gauges shall be 75 percent of the control wire breaking strength.
Towers are desirable because they allow efficient use of limited rooftop space, and offer significant flexibility regarding space planning. Facility B. In the National Electrical Safety Code, Section 39, requirements are listed for environmental factors that should be observed and other applicable requirements contained in Part 3 of the Code. These pathways may consist of aerial, direct-buried, or underground, or a combination of these.
Consideration should be given to prevention, where practicable, of signal interference resulting from vapor and heat shimmer.
TIA/EIA – Wikipedia
See figure 7 for an example of components that may be found in a utility tunnel. Aerial pathways General a Pole class and length b Buried length of the pole c Guying of poles d Pole braces e Pole spacing f g Pole to building span h Tai i Clearance and separation j Pole attachment k Lashing l m Messenger strand n Strand size and tension o Cable sag Slack span Riser Protection 5.
Central connection facility in a hierarchical star topology. These laws are intended to ensure safe work operations and reduce the possibility of damage to existing subsurface facilities. Questions that occur regarding any reduction of these clearances should be discussed with a responsible representative of the owning company.
Where access to both wireline and wireless services is required, the entrance facilities may require adjustment in size, quantity, and location. Where mandated by the AHJ, automatic switchover to standby power shall be provided. When entrance route diversity is developed, entrance routes should be separated by ahsi greatest possible distance. Wikimedia Commons has media related to Computer network. Outdoor closures may be installed in pedestals, maintenance holes, and on poles and cable messenger strands.
Where maintenance holes are installed in roadways, the lid cover shall support heavy vehicular traffic See figure 8. Warning tape, when used, should not be relied upon as a primary locating device for the cable.
Reference should be made to the specific state law in effect. The cross-connect block manufacturer shall designate the recommended cable and wire gauges for each block. The cables shall consist of 19 AWG 0. If there is no specified excavator notification lead time, a minimum of two, or a maximum of ten working days notice should be provided before the excavation site start date. If a cabling system component crosses an environmental boundary, the component or mitigation technique should be selected to be compatible with the worst case environment to which it is exposed.
Because the mechanical splices depend on a physical contact between two cleaved fiber ends, these splices may be more sensitive to large variations in temperature. Maintenance holes are typically used as points of access for pulling and splicing cable. The facility owner is responsible for the engineering and construction of the railroad crossing, including preparing a subsurface profile of the construction site.
This is compared to the breaking strength of an unspliced segment of the same wire. OSP cable intended for aerial use without a support messenger integrated into its design shall be lashed to a support messenger. These closures can be used in a variety of applications including branch splicing. See entrance point telecommunications. The difference between the TA and TB pinouts is that the orange and green wire pairs are exchanged. The maximum length of buried service wire shall not exceed m ft.